New product of Netgear is Smart Wi-Fi Router called Nighthawk R7000 Router, it is not just for connecting to the Internet, but for much more. This new device has the potential to provide improved Wi-Fi speed as well as act as a strong nas storage if connected with an USB 3. 0 external hard drive. If you want to see the manual of the Netgear Nighthawk R7000 you can do so here:
7 Steps to Setup Netgear Nighthawk R7000 Router:
Below is the procedure through which a person has to go in order to configure the Netgear nighthawk r7000 router. Do make sure that the internet service is on before you proceed with the process of installing the router.
1) Remove the antenna caps. This is found on the antenna port of the router.
2) Attach Your Antenna
● Always ensure that you are properly aligning the antenna to the antenna port of the router. Screw them into the antenna ports that have threads.
● Screw these antennas to achieve the optimum wireless signal reception capability. It is suggested that the central antenna should be in the vertical position and the two other antennas are required to tilt outwards at an angle of 45 degrees.
3) Prepare Your Modem
● First, ensure you turn off your modem by unplugging it from any power source.
● If your modem have batteries just remove them.
● If so, then it is probable that your modem is directly connected to another router; thus, disconnect the cable connecting your router and modem.
● To get internet service, you have to ensure that the modem is switched off and connected to a wall jack.
4) Connect the Modem
● The procedures involved in setting up a Netgear r7000 router include plugging in your modem to the electrical outlet and powering it on.
● Now, remove the batteries, and then reinsert them back into the devices.
● It may have arrived with a yellow ethernet cable. Plug the modem into the internet port of the router system.
5) Plug it to a Power Adapter and Then Add Power
● To set up Netgear nighthawk r7000 router, connect your router to the power source and then plug that power source into the wall socket.
● Wait for some time until the power LED light situated at the front panel of the router illuminates.
● When the LED lights are on, press the power button located on the side of the router.
6) Link Your Computer Network
● Connect the computer system through an Ethernet wired or wireless network.
● To achieve a wired connection, use an Ethernet cable and apply the black colored Ethernet port of your router and another end to the computer system.
● To sync it with your Wi-Fi, use the Wi-Fi settings provided in the product sticker.
7) Open an Internet Browser
If you are establishing the connection with your router for the first time, then without any doubt, the genie screen will appear in front of you. Here are some of the procedures you need to follow when it comes to connecting to the internet.
The following are some of the things that you should do if the genie does not appear:
● Switch off the internet browser and switch it on after sometime.
● To setup Netgear nighthawk r7000 router kindly ensure that your PC is connected to any of the LAN ports available in the router.
● If your computer has static IP address then you need to change it in order to get the address assigned by the router.
● If you do not see the genie screen in front of you then in that case you need to log into your router in order to make it easy for genie to find the connection of the network.
Follow These Steps for Logging into the Netgear Nighthawk R7000 Router:
- Open your internet browser
- After that to setup Netgear nighthawk r7000 router, you will have to go to the web address www. routerlogin. net type the following URL into the location bar of your Internet browser.
- You will see a new window right in front of you that is the login screen.
- Write admin in the username text box and type in the password in the password box.
- But the very basic home screen will blink in front of your eyes. If the network connection has not been established properly then the genie will start detecting internet connection on its own.
- Well, these are some of the actions you might need to perform in order to complete the Netgear nighthawk r7000 router installation process.
Netgear Nighthawk R7000 Router Settings
● Next, connect your PC to the router and make these changes: Set a new network name, Create a guest network, and other router settings.
● First, to set up the router one has to connect to the routers Wi-Fi from an iPad or from some other device.
● Open any Web Browser and type www. routerlogin. net.
● Some versions of the server software may require you to enter the admin username and password.
● Choose any one of the options available in the Basic tab for changing the settings of the router.
● This is where to change the name of your network and the password, configure the guest network, and other Nighthawk settings.
● Click on Advanced, then select Administration and set password where you can change the username of the admin and password.
Network Names & Passwords
● One important step is to rename the Nighthawk’s WiFi networks so you can easily connect your registers to them and choose different passwords.
● When in Basic homepage, navigate to the ‘Wireless’ option.
● Input a name, set a security type, and type in a password for the router’s 2. 4GHz network.
● Move down to the next step and perform it for the 5GHz network.
● To ensure the changes made are saved, click ‘Apply’.
● They should reconnect to the WiFi network
Create a Guest Network
- If you would like to allow your customers to use Internet on your network, establish a guest network. Thus, customers can share some data with each other not utilizing the organization’s secure private network.
- On the Basic homepage, first tap ‘Guest Network’.
- Call ‘Guest network’ and give the guest network a name.
- Selected security options: None Choose security type: None Enter password: None
- If you don’t want guests to require entering a password, leave security at its default of ‘None’.
- To make these changes, simply click on ‘Apply’.
Reset Netgear R7000 Router Setup Guide
- You should use a paperclip to attempt a ‘Reset’ button for more than seven seconds.
- Keep the reset button pressed until the power light blinks in the orange color.
- Coordinate your activities with the power light on your router that turns white after rebooting.